Comprehensive Guide to Resetting and Programming Your Lockey Digital Deadbolt

Resetting Your Lockey Digital Deadbolt: Step-by-Step Instructions

If your Lockey digital deadbolt isn’t functioning correctly or if you’ve misplaced the programming code, performing a factory reset can often resolve these issues. A reset restores the lock to its original default settings, erasing all previously stored user codes and configurations. Please note that after a reset, you’ll need to reconfigure the lock from scratch, including programming new user codes and setting your preferences.

Before proceeding, ensure your door remains open and unlocked during the reset process to facilitate proper reprogramming afterward. Follow these detailed steps to perform a complete reset of your Lockey keypad deadbolt:

Open your door and keep it in an unlocked position.
Locate the interior portion of the lock and carefully remove the battery cover.
Identify the small circular reset button labeled R, situated beneath the battery compartment.
Using a pin or a small pointed tool, press and hold the reset button for approximately 5 seconds until you hear three distinct long beeps, signaling the reset process has been completed.
Once the beeps are heard, the lock has been successfully reset and is ready for reprogramming.

Reprogramming After Reset: Essential Initial Steps

Following the reset, it’s crucial to run the door handling identification process to teach your lock the specific orientation of your door—whether it’s a right-handed or left-handed door. Skipping this step could result in improper lock operation. Additionally, you’ll need to establish a new programming code for security purposes, replacing the default code.

Door Handling Identification: How to Set It Up

Performing door handing identification ensures your lock functions correctly relative to your door’s orientation. To do this:

Enter the default programming code, which is 0000.
Press the LOCKEY button.
Press 0 followed by pressing the LOCKEY button again.
If successful, the lock will flash green twice, accompanied by two long beeps, confirming the process is complete.

How to Change the Default Programming Code

The default code (0000) is not secure and should be replaced with a unique code. To update your programming code:

Input the default code (0000) and press the LOCKEY button.
Press 4 and then press the LOCKEY button.
Enter your new 4- to 10-digit code, then press the LOCKEY button to confirm.
Successful change will be indicated by green flashes and two long beeps.

Adding New User Codes for Access

To grant access to others, you can program up to six individual user codes. Each code can be 4 to 10 digits long. Follow these steps to add a new user code:

Enter your current Programming Code and press the LOCKEY button.
Press 1 to initiate user code addition, then press the LOCKEY button.
Input the new user’s code and press the LOCKEY button to save.
Green flashes and two long beeps will confirm the code has been successfully added.

Removing Existing User Codes

If you need to revoke access, you can delete individual user codes as follows:

Enter your Programming Code and press the LOCKEY button.
Press 2 and then press the LOCKEY button.
Input the specific user code you wish to delete, then press the LOCKEY button.
The lock will flash green and emit two long beeps, indicating the code has been successfully removed.

Clearing All User Codes at Once

To delete all user codes simultaneously, follow these instructions:

Enter your Programming Code and press the LOCKEY button.
Press 3 followed by pressing the LOCKEY button.
The lock will flash green and beep twice, confirming all user codes have been cleared.

Important: During this state, keypad access will be disabled. You will only be able to lock or unlock the door using the physical key until you add new user codes.

Enabling or Disabling Auto-Lock Feature

The auto-lock feature ensures your door automatically secures itself after a specified period, providing added security. To activate auto-lock:

Enter your current Programming Code and press the LOCKEY button.
Press 5 and then press the LOCKEY button.
The auto-lock function is now enabled.

To deactivate auto-lock:

Enter your current Programming Code and press the LOCKEY button.
Press 6 followed by pressing the LOCKEY button.
Auto-lock is now disabled.

Additional Resources and Troubleshooting

How to Reset OrangeIOT Keypad Lock
How to Reset Gatehouse Keypad Deadbolt
How to Reset Schlage Encode Deadbolt

Final Tips and Summary

Understanding how to reset and reprogram your Lockey digital deadbolt ensures you maintain control over your home’s security. Remember, successful programming is indicated by green flashes; unsuccessful attempts are signaled with red flashes. If you encounter red flashes, review the steps carefully and repeat the process, ensuring all inputs are accurate and precise. With these instructions, you can confidently reset, reprogram, and manage your lock efficiently, restoring full functionality and security to your entryway.